OF COMPOSITE MACHINING DEPTH WITH USING ACOUSTIC EMISSION

Authors

  • S. F. Filonenko National Aviation University, Kyiv
  • O. V. Zaritskyi National Aviation University, Kyiv
  • A. P. Stakhova National Aviation University, Kyiv

DOI:

https://doi.org/10.18372/1990-5548.54.12334

Keywords:

Acoustic emission, composite material, signal, energy, machining, statistical characteristics

Abstract

The outcomes experimental researches of acoustic emission energy parameters at ascending composite material machining depth are reviewed. The regularity ascending of acoustic emission statistical energy parameters are determined. The sensitivity of acoustic emission energy parameters to ascending of composite material machining depth is determined. It is shown, that the percentage increment of acoustic emission signals energy average level dispersion advances a percentage increment of energy average level and its standard deviation. It is shown that the experimental and theoretical results of the acoustic emission signals energy parameters study have a good agreement.

Author Biographies

S. F. Filonenko, National Aviation University, Kyiv

Educational & Research Institute of Information and Diagnostic Systems

Doctor of Engineering. Professor

O. V. Zaritskyi, National Aviation University, Kyiv

Educational & Research Institute of Information and Diagnostic Systems

Candidate of Science (Engineering). Postdoctoral student

A. P. Stakhova, National Aviation University, Kyiv

Educational & Research Institute of Information and Diagnostic Systems

Candidate of Science (Engineering)

References

N. Mokhtar, I. Y. Ismail, M. Asmelash, H. Zohari, and A. Azhari, “Analysis of acoustic emission on sur-face roughness during end milling,” Journal of Engi-neering and Applied Sciences, vol. 12, no. 4, pp. 1324–1328, 2017.

O. A. Olufayo and K. Abou-El-Hossein, “Acoustic Emission Monitoring in Ultra-High Precision Ma-chining of Rapidly Solidified Aluminum,” Proceed-ings International Conference on Competitive Manufacturing (Coma ’13, 30 January – 1 February 2013 Stellenbosch, South Africa), 2013, pp. 307–312.

A. Hase, “Acoustic Emission Signal during Cutting Process on Super-Precision Micro-Machine Tool,” Proceedings of Global Engineering, Science and Technology Conference 3-4 October 2013, Bay View Hotel, Singapore, ISBN: 978-1-922069-32-0, 2013, 12 p.

D. A. Fadare, W. F. Sales, J. Bonney, and E. O. Ezugwu, “Influence of cutting parameters and tool wear on acoustic emission signal in high-speed turn-ing of Ti-6Al-4V alloy,” Journal of Emerging Trends in Engineering and Applied Sciences, vol. 3(3), pp. 547–555, 2012.

S. J. Ha, B. C. Shin, M. W. Cho, K. J. Lee, and W. S. Cho, “High speed end-milling characteristics of pre-sintered Al2O3/Y-TZP ceramic composites for dental applications,” Journal of the Ceramic Society of Ja-pan, vol. 118, no. 11, pp.1053–1056, 2010.

C. K. Mukhopadhyay, T. Jayakumar, B. Raj, and S. Venugopal, “Statistical Analysis of Acoustic Emission Signals Generated During Turning of a Metal Matrix Composite,” J. of the Braz. Soc. of Mech. Sci. and Eng., vol. 34, no. 2, pp. 145–154, 2012.

Y. Wei, Q. An, X. Cai, M. Chen, and W. Ming, 2015. “Influence of Fiber Orientation on Single-Point Cut-ting Fracture Behavior of Carbon-Fiber/Epoxy Pre-preg Sheets,” Materials, vol. 8, pp. 6738–6751.

P. Kuppan, N. V. Srikanth, and X. A. Raj, “Experi-mental Investigations on Machining of Silica Tiles using Acoustic Emission Technique,” Asian Interna-tional Journal of Science and Technology in Production and Manufacturing Engineering, vol. 5, no. 2, pp.1–12, 2012.

S. F. Filonenko, “Regularity of change of acoustic emission amplitude parameters at prevailing mechanical destruction of composite surface layer,” Bulletin of Engineering Academy of Ukraine, no. 3, 2015, pp. 155–160.

S. F. Filonenko and O. V. Zaritskyi, “Influencing of composite machining speed on experimental regulari-ty of acoustic emission amplitude parameters change,” Electronics and Control Systems, nо. 3(53), pp. 88–94, 2017.

S. F. Filonenko and O. V. Zaritskyi, “Analysis of acoustic emission amplitude parameters when in-creasing the machining depth of a composite,” East-ern-European Journal of Enterprise Technologies, no. 4/1(88), pp. 38–43, 2017.

S. F. Filonenko, “Acoustic radiation energy at a vari-ation of the composite mechanical destruction area,” Proceedings of the National Aviation University, vol. 67, no. 2, 2016, pp. 29–36.

Downloads

How to Cite

Filonenko, S. F., Zaritskyi, O. V., & Stakhova, A. P. (2017). OF COMPOSITE MACHINING DEPTH WITH USING ACOUSTIC EMISSION. Electronics and Control Systems, 4(54), 102–108. https://doi.org/10.18372/1990-5548.54.12334

Issue

Vol. 4 No. 54 (2017)

Section

MATHEMATICAL MODELING OF PROCESSES AND SYSTEMS

License

The scientific journal “Electronics and control systems” adheres to the principles of Open Access and provides free, immediate, and permanent access to all published materials without financial, technical, or legal barriers for readers.

All articles are published in Open Access under the Creative Commons Attribution 4.0 International (CC BY 4.0) license.

Copyright

Authors who publish their works in the journal “Electronics and control systems”:

  • retain the copyright to their publications;

  • grant the journal the right of first publication of the article;

  • agree to the distribution of their materials under the CC BY 4.0 license;

  • have the right to reuse, archive, and distribute their works (including in institutional and subject repositories), provided that proper reference is made to the original publication in the journal.